Archive for April 2019
Configuring Rapid PVST+
0
Langkah-langkahnya dibawah ini :
1. Buka aplikasi Cisco Packet Tracer
2. Buatlah desain skema jaringannya seperti dibawah ini :
1. Buka aplikasi Cisco Packet Tracer
2. Buatlah desain skema jaringannya seperti dibawah ini :
Konfigurasi PC0 :
IP Address : 172.17.10.21
Subnet Mask : 255.255.255.0
Konfigurasi PC1:
IP Address : 172.17.20.22
Subnet Mask : 255.255.255.0
Konfigurasi PC2:
IP Address : 172.17.30.23
Subnet Mask : 255.255.255.0
Konfigurasi Switch 1
S1>enable
S1#configure terminal
S1(config)#vlan 10
S1(config-vlan)#vlan 20
S1(config-vlan)#vlan 30
S1(config-vlan)#vlan 40
S1(config-vlan)#vlan 50
S1(config-vlan)#vlan 60
S1(config-vlan)#vlan 70
S1(config-vlan)#vlan 80
S1(config-vlan)#vlan 99
S1(config-vlan)#int range f0/1-4
S1(config-if-range)#switchport mode trunk
S1(config-if-range)#switchport trunk native vlan 99
S1(config)#int vlan 99
S1(config-if)#ip add 172.17.99.11 255.255.255.0
S1(config-if)#no shutdown
S1(config)#spanning-tree mode rapid-pvst
S1(config)#spanning-tree vlan 1,10,30,50,70 root primary
Konfigurasi Swich 2
S1>enable
S1#configure terminal
S2(config)#int fa0/11
S2(config-if)#switchport mode access
S2(config-if)#switchport access vlan 10
S2(config-if)#spanning-tree bpduguard enable
S2(config-if)#spanning-tree portfast
S2(config-if)#no shutdown
S2(config)#int fa0/18
S2(config-if)#switchport mode access
S2(config-if)#switchport access vlan 20
S2(config-if)#spanning-tree bpduguard enable
S2(config-if)#spanning-tree portfast
S2(config-if)#no shutdown
S2(config)#int fa0/6
S2(config-if)#switchport mode access
S2(config-if)#switchport access vlan 30
S2(config-if)#spanning-tree bpduguard enable
S2(config-if)#spanning-tree portfast
S2(config-if)#no shutdown
S2(config-if)#vlan 10
S2(config-vlan)#vlan 20
S2(config-vlan)#vlan 30
S2(config-vlan)#vlan 40
S2(config-vlan)#vlan 50
S2(config-vlan)#vlan 60
S2(config-vlan)#vlan 70
S2(config-vlan)#vlan 80
S2(config-vlan)#vlan 99
S2(config-vlan)#exit
S2(config)#int vlan 99
S2(config-if)#ip add 172.17.99.12 255.255.255.0
S2(config-if)#no shutdown
S2(config-if)#exit
S2(config)#spanning-tree vlan 1,10,20,30,40,50,60,70,80,99 root secondary
S2(config)#spanning-tree mode rapid-pvst
Konfigurasi Switch 0
S3>enable
S3#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
S3(config)#vlan 10
S3(config-vlan)#vlan 20
S3(config-vlan)#vlan 30
S3(config-vlan)#vlan 40
S3(config-vlan)#vlan 50
S3(config-vlan)#vlan 60
S3(config-vlan)#vlan 70
S3(config-vlan)#vlan 80
S3(config-vlan)#vlan 99
S3(config-vlan)#int range f0/1-4
S3(config-if-range)#switchport mode trunk
S3(config-if-range)#switchport trunk native vlan 99
S3(config)#spanning-tree mode rapid-pvst
S3(config)#spanning-tree vlan 20,40,60,80,99 root primary
S3(config)#int vlan 99
S3(config-if)#ip address 172.17.99.13 255.255.255.0
S3(config-if)#no shutdown
SELESAI
TERIMA KASIH SEMOGA MEMBANTU DALAM PEMBELAJARAN
Konfigurasi Legacy Inter-Vlan Routing
0
Konfigurasi Legacy Inter-Vlan Routing berfungsi Untuk menghubungkan dua buah Vlan yang berbeda dengan menggunakan perintah 'ENKAPSULASI' pada router.
Dibawah ini langkah-langkah konfigurasinya :
1. Buka aplikasi Cisco Packet Tracer Kalian
2. Lalu, Buatlah desain skema jaringannya seperti gambar dibawah ini :
Dibawah ini langkah-langkah konfigurasinya :
1. Buka aplikasi Cisco Packet Tracer Kalian
2. Lalu, Buatlah desain skema jaringannya seperti gambar dibawah ini :
3. Setting IP PC0 dan PC1
PC0 PC1
PC0 PC1
IP address : 192.168.1.10 IP address : 192.168.2.10
Subnet Mask : 255.255.255.0 Subnet Mask : 255.255.255.0
Gateway : 192.168.1.1 Gateway : 192.168.2.1
4. Konfigurasi CLI di Router
Router>enable
Router#configure terminal
Router(config)#interface fastEthernet 0/0.10
Router(config-subif)#encapsulation dot1Q 10
Router(config-subif)#ip address 192.168.1.1 255.255.255.0
Router(config-subif)#exit
Router(config)#interface fastEthernet 0/0.20
Router(config-subif)#encapsulation dot1Q 20
Router(config-subif)#ip address 192.168.2.1 255.255.255.0
Router(config-subif)#exit
Router(config)#interface fastEthernet 0/0
Router(config-if)#no shutdown
Router(config-if)#exit
Router(config)#exit
Router#copy running-config startup-config
Destination filename [startup-config]?
Building configuration...
[OK]
5. Konfigurasi CLI di Switch
Switch>enable
Switch#configure terminal
Switch(config)#vlan 10
Switch(config-vlan)#name BIRU
Switch(config-vlan)#vlan 20
Switch(config-vlan)#name KUNING
Switch(config-vlan)#exit
Switch(config)#interface fastEthernet 0/1
Switch(config-if)#switchport mode trunk
Switch(config-if)#exit
Switch(config)#interface fastEthernet 0/2
Switch(config-if)#switchport mode access
Switch(config-if)#switchport access vlan 10
Switch(config-if)#exit
Switch(config)#interface fastEthernet 0/3
Switch(config-if)#switchport mode access
Switch(config-if)#switchport access vlan 20
Switch(config-if)#exit
Switch(config)#exit
Switch#copy running-config startup-config
Destination filename [startup-config]?
Building configuration...
[OK]
6. Selesai, Sekarang tinggal cek koneksi masing2 pc, seperti dibawah ini :
TERIMA KASIH SEMOGA MEMBANTU DALAM PEMBELAJARAN
